Best amp for highs for your own style

Includes: Amplifier. Birth sheet with tested power. Owner’s manual. Mounting Screws. Warranty.

Features: Rockville dB45 3200 Watt/800 Watt Dyno-Certified RMS 4 Channel Amplifier Car Stereo Amp, Loud!!.

Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). - 2 Ohm: 200 Watts x 4 Channel <1% THD+N . - 4 Ohm:135 Watts x 4 Channel <1% THD+N. - 4 Ohm Bridged: 400Watts x 2 Channel<1% THD+N.

Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). - 2 Ohm: 800 Watts x 4 Channel. - 4 Ohm:540 Watts x 4 Channel. - 4 Ohm Bridged: 1600 Watts x 2 Channel. High-Speed MOSFET Power Supply. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Tertiary Supplies Circuitry. Optical Coupler Class “AB” Technology. Studio-Grade Bipolar Output Stage Transistors.

Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 3KHz. High Pass Filter: 15Hz - 1KHz. Full IC-Controlled Protection Circuitry. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. 8 Volt Preamp Circuitry. Status Mode LED Indicator. Minimum THD at Rated Power: < 0.05%. S / N Ratio: >90dB. Frequency Response: 10Hz - 50KHz. Damping Factor: >150 @ 100Hz. 35 Amp*3 ATC Fuse. Dimensions: (W x H x L) 9" x 2.4" x 21.0"

Power - 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms

Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal

Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry

Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it

Variable Input Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier

Specs - Dimensions: 9.13” x 10.44” x 2.25”, Weight: 4.43 lbs., Speaker Impedance: 2 to 8 Ohm, THD @ RMS Output: 0.01%, S/N Ratio: 102 dB, Frequency Response: 9 Hz to 50 kHz, Fuse Quantity: 1 30 Amp ATO Blade

Warranty - BOSS Audio Systems provides a 6 Year Platinum Online Dealer Warranty for purchases through Amazon.Com. We strongly encourage professional installation of this product to ensure proper functionality

CLASS A/B AMPLIFIER - Class A/B topology ensures high efficiency with big power and minimal distortion. Flexible installation allows this amp to run in two channel or bridged mono mode, maintaining the highest sound quality sound for your car audio.

BUILT FOR POWERFUL SOUND - Minimize heat generation with the PWM MOSFET power supply providing stability through the PC board. Old school Hifonics aluminum heat sink maintains superior heat dissipation to keep your car audio sounding smooth.

MADE TO LAST - Low noise preamplifier generates maximum low voltage signal from source unit, minimizing distortion. High temperature impact resistant inputs with hex screw terminals allow secure connections and are erosion resistant.

HIGH QUALITY CONNECTIONS - RCA outputs and a daisy chain multiple amplifier build eliminates additional signal cables from the source unit. Molded secure connections are used for all wires and angled for ease of access during installation.

CLASSIC HIFONICS LOOK - The ZXX Series maintains the classic feel of Hifonics amplifiers and include an illuminated logo on the front of the amplifier. The Hifonics logo illuminates when the amp is powered, making a statement even in the dark.

500 Watts Max Power

Automatic signal sensing and Turn-On

Hi-Volt input level control

Balanced isolator input circuit

Crunch PX 1000.4 4 Channel Car Amplifier

Power:

2 Ohms: 4 x 250 Watts

4 Ohms: 4 x 125 Watts

Mono Bridged @ 4 Ohms: 2 x 5000 Watts

1400 WATT POWER: The Pyle Dual Channel Car Amplifier is perfect for your vehicle's sound system. Gives you up to 1400W bridgeable output. Features switchable bass boost, variable gain control, configurable electronic crossover network

GOLD-PLATED RCA PORTS: The RCA ports are gold-plated for eliminating signal loss. A subsonic filter allows low-end interference to be cut so your speakers will always deliver the highest quality audio. Features switchable bass boost, low level inputs

MOSFET PULSE: The MOSFET pulse width modulation power supply allows for a clean, distortion-free signal to your compact speakers providing you with crisp and clear audio for an outstanding music experience. Also features anti-thump turn on

THERMAL PROTECTION: To keep both your car and the stereo amp safe, this model is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality sound in a sturdy form factor

SLIM SIZE DESIGN: This box amp's small size makes installation a breeze - you'll have no trouble finding a spot for this little yet powerful device. Additional features include LED indicators, RCA outputs, soft turn-on circuit, remote turn on/off

Power - 300 Max x 2 @ 2 Ohms, 150 Max x 2 @ 4 Ohms, 600 Max Bridged x 1 @ 4 Ohms

Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal

Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers

Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

Fixed High-Pass Crossover - Speakers reproduce sound based on high, low or mid-range frequencies. A high pass crossover gears specifically towards “highs” such as all size speakers including mid ranges and tweeters

Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels

Specs - Dimensions: 7.5” x 10” x 2.4”, Weight: 5 lbs.

Class AB

2Ω stereo & 4Ω bridged full-range operation

Military-grade PCB with PWM MOSFET power supply

Direct short, thermal & overload circuit protection

High/speaker-level & low-level/RCA inputs

Bridgeable

Variable input voltage

QTD (Quick Thermal Dispersion) technology heat sink

Low-noise preamp

Brand new and reliable quality 4 Channel Car Amplifier

Can connect to 4 speakers,6 phase high frequency intermediate frequency low frequency regulation

Double low frequency output,can be push any size Subwoofer within 160W rated power

This 4 channel amp is also equipped with fuse to protect the amplifier and the electrical system of your car from thermal / overload / short circuit conditions.

Sophisticated unit will withstand numerous elements it encounters while on the water

Stainless steel hardware throughout to prevent corrosion, short circuit protection and many other marine specific features

High-speed MOSFET switching power.Preamp inputs

Nickel-plated wire terminals and RCA connectors ensure maximum signal transfer

Protection: Thermal, DC offset, reverse DC voltage and short circuit protection.Fit Type: Universal Fit

The Punch P300X2 is a full chassis (2.38” x 7.76” x 9.86”) 2-channel stereo amplifier, that delivers a rocking 300 Watts of RMS Power

Versatile design for full-range or component systems or can be bridged for use with smaller subwoofers (RMS Power Output: 100 Watts x 2 @ 4-Ohm OR 150 Watts x 2 @ 2-Ohm OR 300 Watts x 1 @ 4-Ohm Bridged)

RCA inputs can accept both Hi and Low level audio signals without the need of a signal converter

Featuring Class-A/B topology, on-board Punch EQ with +18dB boost @ 45Hz, variable 12 dB/Oct Butterworth crossovers, and C.L.E.A.N. Set-up

Famous Rockford Fosgate build quality with a full 1-year warranty when purchased from an authorized Rockford Fosgate reseller

RMS Power Handling @ 4 Ohms: 120 Watts RMS Power Handling @ 2 Ohms: 175 Watts

Alpine ID Sound Quality, solving what’s missing in most car audio systems these days: great spatial imaging and depth of sound stage.

Class-D Performance

Built-in Crossover & Bass EQ

Remote Bass (RUX-KNOB.2) Compatible